# Mongo in Flatland

MongoDB’s geospatial indexing lets you use a collection as a map. It works differently than “normal” indexing, but there’s actually a nice, visual way to see what geospatial indexing does.

Let’s say we have a 16×16 map; something that looks like this:

All of the coordinates in our map (as described above) are somewhere between [0,0] and [16,16], so I’m going to make the min value 0 and the max value 16.

db.map.ensureIndex({point : "2d"}, {min : 0, max : 16, bits : 4})

This essentially turns our collection into a map. (Don’t worry about bits, for now, I’ll explain that below.)

Let’s say we have something at the point [4,6]. MongoDB generates a geohash of this point, which describes the point in a way that makes it easier to find things near it (and still be able to distribute the map across multiple servers). The geohash for this point is a string of bits describing the position of [4,6]. We can find the geohash of this point by dividing our map up into quadrants and determining which quadrant it is in. So, first we divide the map into 4 parts:

This is the trickiest part: each quadrant can be described by two bits, as shown in the table below:

 01 11 00 10

[4,6] is in the lower-left quadrant, which matches 00 in the table above. Thus, its geohash starts with 00.

Geohash so far: 00

Now we divide that quadrant again:

[4,6] is now in the upper-right quadrant, so the next two bits in the geohash are 11. Note that the bottom and left edges are included in the quadrant, the top and right edges are excluded.

Geohash so far: 0011

Now we divide that quadrant again:

[4,6] is now in the upper-left quadrant, so the next two bits in the geohash are 01.

Geohash so far: 001101

Now we divide that quadrant again:

[4,6] is now in the lower-left quadrant, so the next two bits in the geohash are 00.

Geohash so far: 00110100

You may wonder: how far do we keep dividing? That’s exactly what the bits setting is for. We set it to 4 when we created the index, so we divide into quadrants 4 times. If we wanted higher precision, we could set bits to something higher.

You can check your math above by using the geoNear command, which returns the geohash for the point you’re search near:

> db.runCommand({geoNear : "map", near : [4,6]})
{
"ns" : "test.map",
"near" : "00110100",
"results" : [ ],
"stats" : {
"time" : 0,
"btreelocs" : 0,
"nscanned" : 0,
"avgDistance" : NaN,
"maxDistance" : -1
},
"ok" : 1
}

As you can see, the “near” field contains exactly the geohash we’d expect from our calculations.

The interesting thing about geohashing is that this makes it easy to figure out what’s near us, because things are sorted according to their position on the map: every document with a point geohash starting with 00 is in the lower-left quadrant, every point starting with 00111111 is very near the middle, but in the lower-left quadrant. Thus, you can eyeball where a point is by looking at its geohash.

Bits and Precision

Let’s say a wizard casts a ring of fire around him with a radius of 2. Is the point [4,6] caught in that ring of fire?

It’s pretty obvious from the picture that it isn’t, but if we look at the geohash, we actually can’t tell: [4,6] hashes to 00110100, but so does [4.9, 6.9], and any other value in the square between [4,6] and [5,7]. So, in order to figure out whether the point is within the circle, MongoDB must go to the document and look at the actual value in the point field. Thus, setting bits to 4 is a bit low for the data we’re using/queries we’re doing.

Generally you shouldn’t bother setting bits, I’ve only set it above for purposes of demonstration. bits defaults to 26, which gives you approximately 1 foot resolution using latitude and longitude. The higher the number of bits, the slower geohashing gets (conversely, lower bit values mean faster geohashing, but more accessing documents on lookup). If you’re doing particularly high or low resolution queries, you might want to play around with different values of bits (in dev, on a representative data set) and see if you get better performance.

Thanks to Greg Studer, who gave a geospatial tech talk last Friday and inspired this post. (Every Friday, a 10gen engineer does a tech talk on something they’re working on, which is a really nice way to keep up with all of the cool stuff coworkers are doing. If you’re ever running an engineering department, I highly recommend them!)

## 6 thoughts on “Mongo in Flatland”

1. Anonymous says:

Is the bits setting new in 1.9? It looks like it didn’t appear in the wiki until Greg started editing the geospatial page heavily in march. Also for a real world map is their any reason not to use nearsphere?

Like

2. Anonymous says:

Is the bits setting new in 1.9? It looks like it didn’t appear in the wiki until Greg started editing the geospatial page heavily in march. Also for a real world map is their any reason not to use nearsphere?

Like

1. Anonymous says:

No, it just wasn’t documented before.  It’s been around since at least 1.6.0 (probably even 1.4, but I didn’t check).

I can’t think of a time when you wouldn’t want to use spherical coordinates with a real world map, unless precision wasn’t very important to your application.  The numbers are a lot nastier for spherical (stupid pi) so I just used non-spherical to keep things simple.

Like

1. Anonymous says:

Yay, I’m glad someone noticed 🙂

Like

2. Anonymous says:

Yay, I’m glad someone noticed 🙂

Like